Minggu, 25 Juli 2010

Kode Rahasia Pada Handphone

Here *** ALL THE SECRET
CODES *** 4 all gsm
for sumsung
*#9998*228# : Battery status
(capacity, voltage,
temperature)
*#9998*246# : Program status
*#9998*289# : Change Alarm
Buzzer Frequency
*#9998*324# : Debug screens
*#9998*364# : Watchdog
*#9998*377# : EEPROM Error
Stack - Use side keys to select
values. Cancel and ok.
*#9998*427# : Trace
Watchdog
*#9998*523# : Change LCD
contrast - Only with version
G60RL01W
*#9998*544# : Jig detect
*#9998*636# : Memory status
*#9998*746# : SIM File Size
*#9998*778# : SIM Service
Table
*#9998*785# : RTK (Run Time
Kernel) errors - if ok then phn is
reset, info is put in memory
error.
*#9998*786# : Run, Last UP,
Last DOWN
*#9998*837# : Software
Version
*#9998*842# : Test Vibrator -
Flash the screenligth during 10
seconds and vibration
activated.
*#9998*862# : Vocoder Reg -
Normal, Earphone or carkit can
be selected
*#9998*872# : Diag
*#9998*947# : Reset On Fatal
Error
*#9998*999# : Last/Chk
*#9998*9266# : Yann debug
screen (=Debug Screens?)
*#9998*9999# : Software
version
If the up Codes doesn't work,
you should change *#9998* to
*#0. i.e. *#9998*523# change
to *#0523#. An other thing that
will help is to remove your SIM
card. *0001*s*f*t# : Changes
serial parameters (s=?, f=0,1,
t=0,1) (incomplete)
*0002*?# : unknown
*0003*?# : unknown
SP-unlock SGH-600 (and also
SGH-Sgh-600)
*2767*3855# : Full EEPROM
Reset ( THIS CODE REMOVES SP-
LOCK!! )
But also changes IMEI to
447967-89-400044-0. (Doing
this is illegal)
*2767*2878# : Custom EEEPROM
Reset
*These codes have been
tested with version FLD_2C6
G60SB03X of Samsung SGH-600
for d500
*#11[quote]11# S/W Version
*#1234# Firmware Version
*#2222# H/W Version
*#8999*8376263# All Versions
Together
*#8999*8378# Test Menu
*#4777*8665# GPSR Tool
*#8999*523# LCD Brightness
*#8999*377# Error Menu
*#8999*327# EEP Menu
*#8999*3825523# Don't Know.
*#8999*667# Debug Mode
*#92782# PhoneModel (Wap)
#*5737425# JAVA Mode
*#2255# Call List
*#232337# Bluetooth MAC
Adress
*#5282837# Java Version
#*4773# Incremental
Redundancy
#*7752# 8 PSK uplink capability
bit
#*7785# Reset wakeup & RTK
timer cariables/variables
#*1200# ????
#*7200# Tone Generator Mute
#*3888# BLUETOOTH Test
mode
#*#8999*324# ??
#*7828# Task screen
#*5111# ??
#*#8377466# S/W Version & H/
W Version
#*2562# Restarts Phone
#*2565# No Blocking? General
Defense.
#*3353# General Defense,
Code Erased.
#*3837# Phone Hangs on White
screen
#*3849# Restarts Phone
#*3851# Restarts Phone
#*3876# Restarts Phone
#*7222# Operation Typ: (Class
C GSM)
#*7224# !!! ERROR !!!
#*7252# Operation Typ: (Class
B GPRS)
#*7271# CMD: (Not Available)
#*7274# CMD: (Not Available)
#*7337# Restarts Phone
(Resets Wap Settings)
#*2787# CRTP ON/OFF
#*2886# AutoAnswer ON/OFF
#*3737# L1 AFC
#*5133# L1 HO Data
#*7288# GPRS Detached/
Attached
#*7287# GPRS Attached
#*7666# White Screen
#*7693# Sleep Deactivate/
Activate
#*7284# L1 HO Data
#*2256# Calibration info? (For
CMD set DEBUGAUTONOMY in
cihard.opt)
#*2286# Databattery
#*2527# GPRS switching set to
(Class 4, 8, 9, 10)
#*2679# Copycat feature
Activa/Deactivate
#*3940# External looptest
9600 bps
#*4263# Handsfree mode
Activate/Deactivate
#*4700# Please use function
2637
#*7352# BVMC Reg value
(LOW_SWTOFF,
NOMINAL_SWTOFF)
#*2558# Time ON
#*3370# Same as 4700
#*3941# External looptest
115200 bps
#*5176# L1 Sleep
#*7462# SIM Phase
#*7983# Voltage/Freq
#*7986# Voltage
#*8466# Old Time
#*2255# Call Failed
#*5187# L1C2G trace Activate/
Deactivate
#*5376# DELETE ALL SMS!!!!
#*6837# Official Software
Version: (0003000016000702)
#*7524# KCGPRS: (FF FF FF FF
FF FF FF FF 07)
#*7562# LOCI GPRS: (FF FF FF
FF FF FF FF FF FF FF FF FE FF 01)
#*2337# Permanent
Registration Beep
#*2474# Charging Duration
#*2834# Audio Path
(Handsfree)
#*3270# DCS Support Activate/
Deactivate
#*3282# Data Activate/
Deactivate
#*3476# EGSM Activate/
Deactivate
#*3676# FORMAT FLASH
VOLUME!!!
#*4760# GSM Activate/
Deactivate
#*4864# White Screen
#*5171# L1P1
#*5172# L1P2
#*5173# L1P3
#*7326# Accessory
#*7683# Sleep variable
#*8465# Time in L1
#*2252# Current CAL
#*2836# AVDDSS Management
Activate/Deactivate
#*3877# Dump of SPY trace
#*7728# RSAV
#*2677# Same as 4700
#*3797# Blinks 3D030300 in
RED
#*3728# Time 2 Decod
#*3725# B4 last off
#*7372# Resetting the time to
DPB variables
#*7732# Packet flow context
bit Activate/Deactivate
#*6833# New uplink
establishment Activate/
Deactivate
#*3273# EGPRS multislot (Class
4, 8, 9, 10)
#*7722# RLC bitmap
compression Activate/
Deactivate
#*2351# Blinks 1347E201 in RED
#*4472# Hysteresis of serving
cell: 3 dB
#*2775# Switch to 2 inner
speaker
#*9270# Force WBS
#*7878# FirstStartup (0=NO,
1=YES)
#*3757# DSL UART speed set to
(LOW, HIGH)
#*8726# Switches USBACM to
Normal
#*8724# Switches USBACM to
Generator mode
#*8727# Switches USBACM to
Slink mode
#*8725# Switches USBACM to
Loop-back mode
#*3838# Blinks 3D030300 in
RED
#*2077# GPRS Switch
#*2027# GPRS Switch
#*0227# GPRS Switch
#*0277# GPRS Switch
#*22671# AMR REC START
#*22672# Stop AMR REC (File
name: /a/multimedia/sounds/
voice list/ENGMODE.amr)
#*22673# Pause REC
#*22674# Resume REC
#*22675# AMR Playback
#*22676# AMR Stop Play
#*22677# Pause Play
#*22678# Resume Play
#*77261# PCM Rec Req
#*77262# Stop PCM Rec
#*77263# PCM Playback
#*77264# PCM Stop Play
#*2872# CNT
*#8999*283# ???
#*22679# AMR Get Time
*288666# ???
*2886633# ???
*#8999*364# Watchdog
__________________
nokia cdma
*#775738# Pri Seting (enable/
disable)
*3001#12345#
LG CDMA SECRETS CODES
Field Test MENU > 0 > 000000 >
Field Test Other Programming
Secrets:
LGC-300 programming:
menu + 9 and enter SPC:
"000000" or may be other SPC
typed by user. A-Key: press STO
for some time while you can
see special code enter zone.
Type 2539** and enter A-key
LGC-330W programming:
menu + 4 + 0 and enter SPC:
"000000" or may be other SPC
typed by user. A-Key: type
2539** and enter A-key
LGC-800W /500 programming:
menu + 0 and enter SPC:
"000000" or may be other SPC
typed by user. A-Key: type
2539** and enter A-key
LGC-510 programming:
menu + 3 + 0 and enter SPC:
"000000" or may be other SPC
typed by user. A-Key: type
2539** and enter A-key
LG1010, LG4NE1, TP2200,
TP2100, Touchpoint, SB/DB,
TP1100 and TP5200
Press ## Enter the OTKSL Scroll
to SAVE and press OK Scroll to
MIN and press OK Enter 10 digit
MIN scroll to SAVE and press
OK Scroll to SID and press OK
(Skip on 4NE1 go to RESET
PHONE and press OK to
complete) Enter SID (4654) and
scroll to SAVE and press OK
Programming is complete
LG5350
Enter ## and enter the OTKSL
and press the left soft key
under the word “Save” At the
Service Program display select
Mobile Phone # and press the
OK in the center of the 4 way
navigation key Enter the 10
digit MIN and press OK Scroll
down to 4. Advanced and press
OK Scroll to NMSI and press OK
Enter the MSID and press OK
Scroll down to 9. Amps Phone #
and press OK Enter the MSID
and press OK
Press the END key
MOTOROLA PROGRAMING
CODES
Analog Models
Changing the Banner:
#PROGRAM# or [Fcn]
0000000000000 (13 0's)
Field Test: [Fcn] 0 0 * *
TESTMODE [Sto]
Reset Timers: Follow the Field
Test procedure above and then
#32#
Alternative Programming Menu:
#55#
(Not sure): # [SID code]#*
SEND
Programming of various other
models:
V60c Programming Mode:
74663 # [Menu] [Menu] (you
will need the programming
code)
Field Test: [Menu] 073887 *
(you will need the security
code -- try 000000)
To deactivate field test: Power
phone up, hit MENU and the left
button (should bring up the
menu). There's a menu option
for test-mode and at this point
you can turn the menu off and
return the phone to normal.
Alternatively press menu and
then the nearest button to the
left (Phone book button) quickly
and it will take you back to the
main screen and your phone
will look normal.
StarTac 7790
Field Test: [Fcn] 0 0 * *
TESTMODE [Sto]
StarTac 7760, 7860
Field Test: [Fcn] 0 0 * *
TESTMODE [Sto] Service Menu:
[Fcn] 0 000000 000000 RCL
Complete system test (most
models): (Phone OFF), Hold
down any row of keys (1+2+3,
4+5+6, etc) and turn the phone
ON
To access the diagnostic mode
on the I30: #, *, MENU,
JOYSTICK-RIGHT (Do these
keystrokes fast)
To access the diagnostic mode
on any of the older iDEN phones
(pre-i1000): VOLUME DOWN,
MENU, MENU, MENU, LEFT,
MENU, MENU, LEFT (this is the
reverse of the test menu
routine)
To access the diagnostic mode
on any of the new models
(i1000+, i700+, i550+, etc): Hold
down any three keys in a row
across.
The unit will enter the test
mode and can be stepped
through the various functions
with the keys and buttons. At
the end of the test, power
cycle the unit to return to
normal function. This test will
check various phone functions,
including LCD display, speaker,
earphone, microphone, LEDs,
vibrator, backlight and all of the
buttons and keys for the newer
models
SAMSUNG CDMA SECET CODES
Older Models:
NAM Programming:
47*869#08#9
Test mode: *759#813580 OR
5809540*45680
Exit Test Mode: 02 A-Key: menu
+ 0,
code 25##
Samsung SPH-T100
MENU 820 > 810325
Samsung SCH-3500
MENU 820 > 295184
Programming of various other
models:
Samsung A500
Enter ## and the 6 digitOTKSL
SERVICE MENU will appear and
1.Basic will be highlighted
Press OK Device will display
NAM CDMA/ Phone Number
Enter 10 digit MIN Press OK (3
times) Display will return to
Service Menu.
Press END. Programming is
complete
Samsung N240 and N400
Enter ## and type in the 6 digit
OTKSL
The display will show SVC
MENU and 1. Phone Number
Press OK Enter the 10 digit MIN
and press OK
The display will show NAM with
Home SID on the second line
(Note: SID is no longer used)
Press OK
The display will return to the
SVC MENU
Press END to complete the
programming
Samsung N300
Press ## followed by the
OTKSL
SVC menu will be displayed
Press 1 for Phone #
Enter the 10 digit MIN and press
OK
MIN that was entered will be
displayed press OK
SVC Menu will display press 3
for NAM
Enter the 4 digit Home SID
press OK
Press END and handset will
power cycle
Samsung i300
Tap on the Phone Icon with
stylus
Press #907*9#0 ENTER LOCK
should appear on screen
ENTER OTKSL
SVC MENU will appear press 1
Enter 10 digit MIN and then
press SAVE
Press SAVE again
Press 3 and then press SAVE 6
times
Enter the HOME SID and press
SAVE once
Press END key twice
Samsung A400 and A460
Enter ## and OTKSL
Press 1 for Basic at MENU (1 of
Phone # when using the MSL)
Enter 10 digit MIN and press OK
At 1.Basic Menu press the END
key
Handset will power cycle
Samsung 3500, 8500, 6100, and
N200
Press MENU
Press 6 0 (3500) 8 2 0
(8500/6100/N200)
Enter OTKSL
Press 1 at SVC MENU Screen
Enter MIN and press OK
Press OK 4 times
Enter SID (4654) and press OK
Press END key
Programming is complete
gsm NOKIA SECRET CODES
Nokia CodesThese Nokia codes
will work on most Nokia mobile
phones, however we accept no
responsibility of any kind for
damage done to your phone
whilst trying these Nokia
secret codes.
Nokia code Code function
*3370# This Nokia code
activates Enhanced Full Rate
Codec (EFR) - Your Nokia cell
phone uses the best sound
quality but talk time is reduced
my approx. 5%
#3370# Deactivate Enhanced
Full Rate Codec (EFR)
*#4720# Activate Half Rate
Codec - Your phone uses a
lower quality sound but you
should gain approx 30% more
Talk Time
*#4720# With this Nokia code
you can deactivate the Half
Rate Codec
*#0000# Displays your phones
software version, 1st Line :
Software Version, 2nd Line :
Software Release Date, 3rd
Line : Compression Type
*#9999# Phones software
version if *#0000# does not
work *#06# For checking the
International Mobile Equipment
Identity (IMEI Number)
#pw+1234567890+1# Provider
Lock Status. (use the "*" button
to obtain the "p,w" and "+"
symbols)
#pw+1234567890+2# Network
Lock Status. (use the "*" button
to obtain the "p,w" and "+"
symbols)
#pw+1234567890+3# Country
Lock Status. (use the "*" button
to obtain the "p,w" and "+"
symbols)
#pw+1234567890+4# SIM Card
Lock Status. (use the "*" button
to obtain the "p,w" and "+"
symbols)
GSM SAMSUNG SECRET CODES
*#06# -> Show IMEI
*#9999# -> Show Software
version
*#0837# -> Show Software
Version (instructions)
*#0001# -> Show Serial
Parameters
*#9125# -> Activates the
smiley when charging.
*#9998*228# -> Battery status
(capacity, voltage,
temperature)
*#9998*246# -> Program
status
*#9998*289# -> Change Alarm
Buzzer Frequency
*#9998*324# -> Debug
screenslect values. Cancel and
ok.
*#9998*427# -> Trace
Watchdog
*#9998*523# -> Change LCD
contrast - Only with version
G60RL01W
*#9998*544# -> Jig
detectService Table
*#9998*785# -> RTK (Run Time
Kernel) errors - if ok then phn is
reset, info is put inmemory
error.
*#9998*786# -> Run, Last UP,
Last DOWN
*#9998*837# -> Software
Version
*#9998*842# -> Test Vibrator -
Flash the screenligth during 10
seconds and vibrationactivated.
*#9998*862# -> Vocoder Reg -
Normal, Earphone or carkit can
be selected
*#9998*872# -> Diag
*#9998*947# -> Reset On Fatal
Error
*#9998*999# -> Last/Chk
*#9998*9266# -> Yann debug
screen (=Debug Screens?)
*#9998*9999# -> Software
version
*0001*s*f*t# -> Changes serial
parameters (s=?, f=0,1, t=0,1)
(incomplete)
*0002*?# -> unknown
*0003*?# -> unknown SP-
unlock SGH-600 and SGH 2100
*2767*3855# -> Full EEPROM
Reset ( THIS CODE REMOVES SP-
LOCK!! ) But also changes IMEI
to 447967-89-400044-0
*2767*2878# -> Custom
EEEPROM Reset These codes
has been tested with version
FLD_2C6 G60SB03X of Samsung
SGH-600 type 8889 instead of
9998.
GSM MOTOROLA SECRET
MOBILE CODES
Motorola
IMEI number: * # 0 6#
Net Monitor ON: * * * 1 1 3 * 1 *
[OK]
Net Monitor OFF: * * * 1 1 3 * 1 *
[OK]
* - press this until box shown up
To activate RBS:
(pause means the * key held in
until box appears)
[pause] [pause] [pause] 1 1 3
[pause] 1 [pause] [ok]
You now have to press the
[MENU] and scroll to the 'Eng
Field Options' function with the
keys, and enable it.
To de-activate RBS,
[pause] [pause] [pause] 1 1 3
[pause] 0 [pause] [ok]
This only works with some
versions of software. Please
report what works and doesn't
for you.
Reported working, by country:
d460: IT
6200 Flare: UK (Orange), AU
7500: IT (model: F16 HW: 5.2
SW: 2.1)
8200: ES, AU, NL, BE
8400: IT, NL
8700: AU, IT, SG, DE, ES, ZA
Uses of RBS:
Distance From Base Station -
Place a call, when it is
answered, press [MENU] until
'Eng Field Option' is displayed,
press [OK], select 'Active Cell',
press [OK], press [MENU] until
'Time Adv xxx' appears, where
xxx is a number. Multiply this
number by 550, and the result is
the distance from the RBS
(Radio Base Station), in meters.
Signal Quality - press [MENU]
until 'Eng Field Option' is
displayed, press [OK], select
'Active Cell', press [OK], press
[MENU] until 'C1' appears. This is
the signal quality. If it becomes
negative for longer than 5
seconds, a new cell is
selected.
SONY ERICSSON SECRET CODE
General Secrets
IMEI (International Mobile
Equipment Identity): *#06#
Firmware Version: >*<<*<* Programming Checks: >*<<*<*>
or >*<<*<*>
Accessing the phone without a
SIM card:
**04*0000*0000*0000# then
on 'Wrong Pin' No
Reset English Menu: *#0000#
300, 600, 700 Series
Programming Menu (Short): 987
+ >
Programming Menu (Long):
923885 + >
Field Test: 904090 + > (to exit
904090 + >)
Phone Test: 904059 + > (to exit
3 + <) Phone Reset: 904060 + >
CDMA Mode: 904093 + menu
Analog Mode: 904095 + menu
DM mode 904959 + menu
GSM PHILIPS SECRET CODES
Philips GENIE
To view IMEI number *#06#
*#2254*# is the statusregister:
C, BS, RR, MMI, CREAT.
*#2255*# will activate and
deactivate the "DEBUG CALL"-
Mode
*#2558*# will display the time
in days,hours and minutes you
are connected to the GSM
network
To force a reconnection to the
network, type : *#2562*#
To view and modify the
Security Code of the phone,
type: *#7489*#
To view some info about your
SIM card like the phase level,
the name, type: *#7378*#
To obtain information on SIM
lock, Init and Flags, press:
*#3377*#
To activate or deactivate Sleep
Mode: *#7693*#
To get info about Sleep Mode:
*#8463*#
Philips FIZZ
IMEI: *#06#
Lock Code: *#1234#
Software Version
To find software version, enter
*#8377*#
The output will look something
like:
Version : 0916 - EEPROM :
00000000-00 - TDA : 2445 -
KISS : 0502 SIM-LCK
..or extended software version
*#5644*#
output:
Version : 09162205 - EEPROM :
00000000-00 - TDA : 2445 -
KISS : 0502 SIM-LCK
SM ALCATEL SECRET MOBILE
CODES
ALCATEL
* # 0 6 # : IMEI number
* # 0 6 # : Software version
0 0 0 0 0 0 * : Net Monitor
PINOUTS AND CODES FOR
PANASONIC MOBILES
Panasonic G500
IEMI:
To view IMEI number *#06#
--------------------------------------------------------------------------------
PINOUTS
1 - Ground
2 - TX_Audio
3 - Audio_Ground
4 - HF_ON (L=ON) -> L=H/F ON
5 - AOP_Sense <- Data Adaptor Select 6 - Serial_Up <- UART up (9600,33.8kbps) 7 - Serial_Down -> UART down
8 - External_Power <- POWER FOR CHARGING 9 - Ground 10 - RX_Audio 11 - Radio_Mute -> L=MUTE
12 - HF_Sense <- L=H/F MODE 13 - Reserved L=FLASH WRITE ENABLE 14 - Ignition <- H=ON 15 - Logic_Power -> H=HANDSET
ON
16 - PAON -> Power Amplifier
Control Signal.
**************************************************
**
Nokia 3310 Secret codes
Jul, 08 2003 - 06:20
contributed by: mef
*#06# To find IMEI
(International Mobile Equipment
Identity)
*#7780# Restores Factory
Settings..(Memory, language,
counters not included)
*#3110# For checking the
phone's software (SW) - called
firmware revision information.
*#746025625# [*#sim0clock#]
To check if the Sim-Clock can
be Stopped (Sim-clock-stop is a
kind of standby mode which will
save battery time)
*#92702689# [*#war0anty#]
Phone asks 'warranty code:'
6232 (OK) Displays the Month
and Year of Manufacture
9268 (OK) Displays Serial
Number
7332 (OK) Displays the date of
the last repairment - if found
7832 (OK) Displays (if found) the
date where the phone was
purchased
37832 (OK) Set the Purchasing
Date MMYY (This date can be
set only once!)
87267 (OK) Transfers ALL phone
numbers, Logo's, and ringtones
from other gsm phones
Nokia 101 cell phone lockcode
Jul, 10 2000 - 02:35
Nokia 101 cell phones set up by
Bell Mobility in Toronto can
have their lock code
circumvented by the following
method:
Type: * 3001 # 12345 [STO] 00
Wait for: NOT DONE
Type: [RCL] 01
Clear old lock code (the last
four digits) and enter a new
lock code. Be very careful not
to delete other characters.
Type: [STO] 01 [STO]
Turn power off.
Nokia 9000/9000i
Nov, 25 2000 - 22:41
To view IMEI number *#06#
To view Software Version
enter *#8110# Latest Version is
under Phone Info.
To view Week and Year of
manufacture enter *#3283#
Samsung SGH-600 / SGH-2100
Secret Codes
*#06# -> Show IMEI
*#9999# -> Show Software
Version
*#0837# -> Show Software
Version (instructions)
*#0001# -> Show Serial
Parameters
*#9125# -> Activates the
smiley when charging.
*#9998*228# -> Battery status
(capacity, voltage,
temperature)
*#9998*246# -> Program
status
*#9998*289# -> Change Alarm
Buzzer Frequency
*#9998*324# -> Debug
screens
*#9998*364# -> Watchdog
*#9998*377# -> EEPROM Error
Stack - Use side keys to select
values. Cancel and ok.
*#9998*427# -> Trace
Watchdog
*#9998*523# -> Change LCD
contrast - Only with version
G60RL01W
*#9998*544# -> Jig detect
*#9998*636# -> Memory status
*#9998*746# -> SIM File Size
*#9998*778# -> SIM Service
Table
*#9998*785# -> RTK (Run Time
Kernel) errors - if ok then phn is
reset, info is put in memory
error. *#9998*786# -> Run, Last
UP, Last DOWN
*#9998*837# -> Software
Version
*#9998*842# -> Test Vibrator -
Flash the screenligth during 10
seconds and vibration
activated.
*#9998*862# -> Vocoder Reg -
Normal, Earphone or carkit can
be selected
*#9998*872# -> Diag
*#9998*947# -> Reset On Fatal
Error
*#9998*999# -> Last/Chk
*#9998*9266# -> Yann debug
screen (=Debug Screens?)
*#9998*9999# -> Software
version
*0001*s*f*t# -> Changes serial
parameters (s=?, f=0,1, t=0,1)
(incomplete)
*0002*?# -> unknown
*0003*?# -> unknown
SP-unlock SGH-600 and SGH
2100
*2767*3855# -> Full EEPROM
Reset ( THIS CODE REMOVES SP-
LOCK!! )
But also changes IMEI to
447967-89-400044-0, To
restore your old IMEI use the
IMEI program found on the
software page.
*2767*2878# -> Custom
EEEPROM Reset
These codes has been tested
with version FLD_2C6 G60SB03X
of Samsung SGH-600
Samsung 811
Jul, 08 2000 - 01:24
47*869#08#9
- unlock code / change roaming
code / ID
SIEMENS S1 / S3 / S3 COM / S4
To view the software date and
else with S3 com, S4, S4Power
press with SIM removed *#06#
and left softkey.
To view some other stuff with
S4Power
press with SIM removed *#06#
and left softkey twice.
To view the software date with
S3 com, S4, S4Power
press with SIM installed menu
98 and left softkey twice.
ACTIVATE MONITOR MODE
Siemens S1/S3
Menu, 9 (Phone Options), 7
(Phone Status), Left Display
Button (left MENU key),
5553756, HangUp Button (Red
HandSet key)
Siemens S3 COM/S4
Menu, 9 (Phone Options), 7
(Phone Status), Left Display
Button
(left MENU key), 7684666,
HangUp Button (Red HandSet
key)
Note: Now Monitor should
appear at the bottom of the
Network Options menu.
MONITOR MODE
Pressing the right Display
Button when in monitor mode
will toggle into 1 and 2 modes
Pressing the right Display
Button when in monitor mode
will show a
list of the six cells with the
strongest signals.
Test Mode Indicators: (* = only
available when call in
progress )
CH Channel Number
RX Signal Strength (dB)
N NCC (Colour Code)
B BCC (Colour Code)
CI Cell ID (in Hex)
C1+ How long before phone
does forced hand over.(see RX
and RXAM)
LAI Location Area Identity.
Display Network ID code
(42F010 = 240.01) and MSC
TXPWR Transmit Power (dB)
RXAM Receive signal strength
cut-off point
TS* Time Slot Number
TA* Timing Advance. Distance
from tower in Km X 2
PL* Power Level
SIEMENS S1
Here's a trick to play Tetris,
also known as Klotz on a
Siemens S1.
Turn the phone on. Enter PIN.
Before the telephone has
logged in to the
your GSM net do the following
steps.
1: Choose F 9 (function
settings)
2: Choose send own number
and push the right button for
choose.
3: Push 9
USE 2 as < and 8 as > , rotate the
klotz with 5 and drop with 4.
I have just heard from one of
the programmers of the phone
that Tetris
was in the phone during
development, but it was
removed before it was
produced.
Apparantly someone has the
patent on games in mobile
phones and Siemens
didn't want to pay the licensing
fees. It was either in Menu
F-9-9 or it's not there at all
Siemens C 25
Secret Codes
SP unlock *#0003*(secret code
8 digits)#
*#06# for checking the IMEI
(International Mobile Equipment
Identity)
Resets language to automatic
selection : * # 0000 # then
Green button
Pin Out
1- GND
2- SB
3- POWER
4- NC
5- TX
6- RX
7- CLOCK
8- DATA
9- GND MIC
10- HF MIC
11- AUDIO
12- GND AUDIO
Sagem MC959
Secret Codes
MC959
in main menu press * for hot-
menu:
lcd, led, vibra, tests, imei,
software versions, battery
voltage
Type MENU - 5 - 1 - 1 - # to
enter Engineering menu on
SAGEM (RC-712, 721, 815 and 815
plus) phones.
Panasonic G500
IEMI:
To view IMEI number *#06#
--------------------------------------------------------------------------------
PINOUTS
1 - Ground
2 - TX_Audio
3 - Audio_Ground
4 - HF_ON (L=ON) -> L=H/F ON
5 - AOP_Sense <- Data Adaptor Select 6 - Serial_Up <- UART up (9600,33.8kbps) 7 - Serial_Down -> UART down
8 - External_Power <- POWER FOR CHARGING 9 - Ground 10 - RX_Audio 11 - Radio_Mute -> L=MUTE
12 - HF_Sense <- L=H/F MODE 13 - Reserved L=FLASH WRITE ENABLE 14 - Ignition <- H=ON 15 - Logic_Power -> H=HANDSET
ON
16 - PAON -> Power Amplifier
Control Signal.
Mitsubishi MT- D30
Secret Codes
Monitor mode: Hold C and press
379
Secret menu: Hold C and press
987
Version number: Hold C and
press 597
Phase1 and 2 : Hold C and press
499
Warm start : Hold C and press
179
Instant turn off: Hold C and
press 999
Unlock menu: Hold C and press
787090
Mitsubishi Trium
*#0000# to reset the phones
menu-language to natural
language, set initially by the
distributor.
*#06# for checking the IMEI
(International Mobile Equipment
Identity)
hold * then 5806 - show
software version
hold * then 5807 - a littel bit
diffrent
hold * then 5472 - Testmode for
datacable (it seems so)
hold * then 4329 - Activate and
deactivate NETMONITOR
hold * then 621342 - Activate
and deactivate another
NETMONITOR
hold * then 3926 - shutdown
SP lock
You can turn around the lock
routin by entering
**04*PIN*PIN*PIN# now the
secretcode change was applied
and the software turns back to
main menue. It works not on all
triums, only on thos with older
sofware versions
SIEMENS S1 / S3 / S3 COM / S4
To view the software date and
else with S3 com, S4, S4Power
press with SIM removed *#06#
and left softkey.
To view some other stuff with
S4Power
press with SIM removed *#06#
and left softkey twice.
To view the software date with
S3 com, S4, S4Power
press with SIM installed menu
98 and left softkey twice.
ACTIVATE MONITOR MODE
Siemens S1/S3
Menu, 9 (Phone Options), 7
(Phone Status), Left Display
Button (left MENU key),
5553756, HangUp Button (Red
HandSet key)
Siemens S3 COM/S4
Menu, 9 (Phone Options), 7
(Phone Status), Left Display
Button
(left MENU key), 7684666,
HangUp Button (Red HandSet
key)
Note: Now Monitor should
appear at the bottom of the
Network Options menu.
MONITOR MODE
Pressing the right Display
Button when in monitor mode
will toggle into 1 and 2 modes
Pressing the right Display
Button when in monitor mode
will show a
list of the six cells with the
strongest signals.
Test Mode Indicators: (* = only
available when call in
progress )
CH Channel Number
RX Signal Strength (dB)
N NCC (Colour Code)
B BCC (Colour Code)
CI Cell ID (in Hex)
C1+ How long before phone
does forced hand over.(see RX
and RXAM)
LAI Location Area Identity.
Display Network ID code
(42F010 = 240.01) and MSC
TXPWR Transmit Power (dB)
RXAM Receive signal strength
cut-off point
TS* Time Slot Number
TA* Timing Advance. Distance
from tower in Km X 2
PL* Power Level
SIEMENS S1
Here's a trick to play Tetris,
also known as Klotz on a
Siemens S1.
Turn the phone on. Enter PIN.
Before the telephone has
logged in to the
your GSM net do the following
steps.
1: Choose F 9 (function
settings)
2: Choose send own number
and push the right button for
choose.
3: Push 9
USE 2 as < and 8 as > , rotate the
klotz with 5 and drop with 4.
NEW CODE
Alcatel
Master Codes
- 25228352
- 25228353
- 83227423
(TH3/4,BH4,BF5,BG3,BF3/4..)
###337*07# - master reset
(with SIM)
###847# - factory reset (with
SIM)
###728# - factory reset (with
SIM)
Alcatel 835 formating - **0102#
Samsung
*2767*3855# - FULL E2P RESET
*2767*2878# - CUSTOM E2P
RESET
#*7337# - UNLOCK
*2767*688# - UNLOCK
*#0523# - CONTRAST
*#9998*523# - CONTRAST
*#8999*8378# - Service Menu
(X100)
Philips
#20021208# ok - 630 without
SIM (erase flash)
*#7728*# - RSAV DONE
*#3849*# - ??? reboot
*#3851*# - ??? reboot
Philips 568 *01763*737381# -
reset
Pantech
*01763*737381# - master reset
(user data, user code) without
SIM
*01763*8371# - SW version
*01763*6371# - UNLOCK
*01763*3641# - Menu
Panasonic
*01763*737381# - master reset
(user data, user code) A100,
A101, A102,G50, G51, G70,
GD55..
*369# :-) - MENU
7, 4, 6, menu, menu - lock menu
*#9999# - 5 sec after power
on - SW version (GD75, GD67,
GD87..)
LG
2945#*# - service menu (code
reset)(W3000 G5300 C1200
G7100...)
2945# :-)- hold (LG 500,600)
B1200 *+pwr, 6,6,8 Service
Menu
B1300 *+pwr, 1,5,9 Service
Menu
Security Removing Code For Lg
8110,8120.
47328545454#
Or
277634#*#
Sony-Ericsson
> * < < * < * - Service menu
< * * < - Lock menu
VK Mobile
*#79# - SW version
*#85*364# :-) - hold menu
855855# without SIM (VG107)
85558555# :-)-hold
4268# :-)-hold (VG207)
Voxtel
0124 - master code
0718# :-)- hold - menu (ST11,
SC10, V100 without SIM)
4268# :-)- hold - show code
(ST11, SC10 without SIM)
*789(#)- hold - menu (V50,
V300, RX100 without SIM)
Motorola
(T190, T191, T205) master code
- 19980722
- 20010903
**********
P2K test menu:
*#06#, menu, menu, 048263*
Test comands:
32*116*1*0*0 - read phone
code
32*118*1*0*0 - read security
code
18*0 - factory reset, phone
code off
18*1 - master reset
54*18*1 - full phone reset
10*0*6 - select 900/1800
32*279*1*0*8 - model
32*383*1*0*0 - flex version
Hard reset MPX200, MPX220 -
blue button + power on
Nokia
*#7370925538# (valet code
reset) 6230
*#746025625# [*#sim0clock#]
*#92702689# [*#war0anty#]
Fly Bird
S688 - #*301#02# send - with
SIM
menu:
7 - 10 - ok,
#*8000#, #*3676# (reboot
repair)
V09, S1180 - *, 3 times down, 3
times up - service menu
Enol
*#987*00# - Service menu
*#987*99# - Full reset
*#900# - SW version
Maxon
*#9922# - menu, reset
(without SIM)
*#9900# - Software Version
*#9901# - Software Version
(PBatch)
S60 Siries (SX1, 6600, N-Gage..)
*#7780# - factory default
*#7370# - full factory defaults
(all user data reset)
SX1 formating - * + # + power
on
6600 formating - 3 + * + send +
power on
Sendo X1 formating - 5 + power
on
Mitsubishi
*65512890 (*-hold) format FFS
(Eclipse)
* 3926 - (*-hold) test mode
* 5806 - (*-hold) SW version
*(hold) 787090 - trium 320
unlock menu
Huawei (cdma)
MASTER SECURITY CODE
-309296
-3092
-9296
Pantech HX-550C (cdma)
Full reset (phone code reset)-
##03*934#9367*192#397#7412569746
PWR,
after reset - ##27732726 PWR
and select "with uim"
Audiovox 107 45680*47*869#1
Audiovox 120 #86904**89397#
Audiovox 130,100,8300,8600
##20022002"END"1
AUDIVOX 7900
MENU# ПИСЬМО*1 10СЕК
Audiovox 4000,9500 289F#1
CyberBell 100
##1475369908##"save"
Ericsson 923885"Menu"
EVRC #763*FF
GTRAN GCP-2000 01#737
Hunday-110 #86904**89397#
Hunday-600
##20022002"END"1 код
100499
LG-300 "Menu" 9
LG-330 "Menu" 40
LG CX300V Menu 0
LG-800 "Menu" 0
Programming:
Samsung
All type of phones (old
modeles):
NAM programming:
47*869#08#9
Test mode: *759#813580 or
5809540*45680
exit test mode - 02
A-Key: menu + 0, code 25##
Samsung A500
1. Enter ## and the 6 digit
OTKSL
2. SERVICE MENU will appear
and 1.Basic will be highlighted
3. Press OK
4. Device will display NAM
CDMA/ Phone Number
5. Enter 10 digit MIN
6. Press OK (3 times)
7. Display will return to Service
Menu. Press END.
8. Programming is complete
Samsung N240 and N400
1. Enter ## and type in the 6
digit OTKSL
2. The display will show SVC
MENU and 1. Phone Number
3. Press OK
4. Enter the 10 digit MIN and
press OK
5. The display will show NAM
with Home SID on the second
line (Note: SID is no longer
used)
6. Press OK
7. The display will return to the
SVC MENU
8. Press END to complete the
programming
Samsung Uproar
1. Press MENU key
2. Enter 9 2 0
3. Enter the OTKSL
4. At SVC Menu screen press
OK
5. Enter MIN and press OK 4
times
6. Enter SID (4654) and press
OK
7. Press END key
8. Programming is complete
Samsung N300
1. Press ## followed by the
OTKSL
2. SVC menu will be displayed
3. Press 1 for Phone #
4. Enter the 10 digit MIN and
press OK
5. MIN that was entered will be
displayed press OK
6. SVC Menu will display press 3
for NAM
7. Enter the 4 digit Home SID
press OK
8. Press END and handset will
power cycle
Samsung i300
1. Tap on the Phone Icon with
stylus
2. Press #907*9#0 ENTER LOCK
should appear on screen
3. ENTER OTKSL
4. SVC MENU will appear press 1
5. Enter 10 digit MIN and then
press SAVE
6. Press SAVE again
7. Press 3 and then press SAVE
6 times
8. Enter the HOME SID and press
SAVE once
9. Press END key twice
Samsung A400 and A460
1. Enter ## and OTKSL
2. Press 1 for Basic at MENU (1
of Phone # when using the MSL)
3. Enter 10 digit MIN and press
OK
4. At 1.Basic Menu press the
END key
5. Handset will power cycle
Samsung 3500 8500 6100 N200
1. Press MENU
2. Press 6 0 (3500) 8 2 0
(8500/6100/N200)
3. Enter OTKSL
4. Press 1 at SVC MENU Screen
5. Enter MIN and press OK
6. Press OK 4 times
7. Enter SID (4654) and press
OK
8. Press END key
9. Programming is complete
Qualcomm
QCP-800 programming: menu +
3 + 0.
SPC: "000000" or may be other
SPC typed by user.
QCP-820/1920/2035: type
"111111" and press Jog Dial.
Choose "Programming" and
enter SPC: "000000" or may be
other SPC typed by user.
QCP 1960 and 2760
1. Press softkey under the work
MENU
2. Press 8 0
3. Enter the OTKSL
4. Press softkey for OK
5. Enter MIN and press softkey
for OK
6. No SID is require for this
handset
7. Press softkey for EXIT
8. Programming is complete
LG
LGC-300 programming: menu +
9 and enter SPC: "000000" or
may be other SPC typed by user
A-Key: press STO for some
time while you can see special
code enter zone. Type 2539**
and enter A-key
LGC-330W programming: menu
+ 4 + 0 and enter SPC: "000000"
or may be other SPC typed by
user.
A-Key: type 2539** and enter
A-key
LGC-800W /500 programming:
menu + 0 and enter SPC:
"000000" or may be other SPC
typed by user.
A-Key: type 2539** and enter
A-key
LGC-510 programming: menu +
3 + 0 and enter SPC: "000000"
or may be other SPC typed by
user.
A-Key: type 2539** and enter
A-key
LG1010 LG4NE1 TP2200 TP2100
Touchpoint SB/DB TP 1100
TP5200
1. Press ##
2. Enter the OTKSL
3. Scroll to SAVE and press OK
4. Scroll to MIN and press OK
5. Enter 10 digit MIN scroll to
SAVE and press OK
6. Scroll to SID and press OK
(Skip on 4NE1 go to RESET
PHONE and press OK to
complete)
7. Enter SID (4654) and scroll to
SAVE and press OK
8. Programming is complete
LG5350
1. Enter ## and enter the OTKSL
and press the left soft key
under the word “Save”
2. At the Service Program
display select Mobile Phone #
and press the OK in the center
of the 4 way navigation key
3. Enter the 10 digit MIN and
press OK
4. Scroll down to 4. Advanced
and press OK
5. Scroll to NMSI and press OK
6. Enter the MSID and press OK
7. Scroll down to 9. Amps
Phone # and press OK
8. Enter the MSID and press OK
9. Press the END key
TP 2100
1. Press ##
2. Enter OTKSL
3. Scroll to SAVE and press
Roller Ball in for OK (ESN will
display)
4. Select NEXT (by pressing in
the roller ball)
5. Scroll to EDIT and press in
the roller ball
6. Enter MIN
7. Scroll to SAVE and press
roller ball in
8. Select NEXT at the next 3
screens and then EXIT
9. Programming is complete
TP3000
1. Press ##
2. Enter OTKSL
3. Scroll to SAVE and press OK
4. Open flip
5. Use Stylus to enter the 10
digit MIN
6. Press OK (No SID entry is
required)
7. Programming is complete
TP 5250
1. Press ##
2. Enter the OTKSL
3. Scroll to SAVE and press OK
4. The phone display will read
SVC Program
5. Scroll to MOBILE PHONE # and
press OK
6. Phone display will read
Mobile Phone Number
7. Enter the 10 digit MIN and
press OK
8. Scroll to Home SID and press
OK
9. Enter the 4 digit SID (4654)
and press OK
10. Reset Phone will be
highlighted. Press OK
11. Phone will reset
12. Programming is complete
LG V111(DM110)
[menu]30.
After ask lockcode, enter:
843691.
Ericsson
Programming:
Shot NAM 987 + menu
Long NAM 923885 + menu and
enter SPC: "000000" or may be
other SPC typed by user.
CDMA mode 904093 + menu
Analog mode 904095 + menu
DM mode 904959 + menu
Hyundai
HGC-120E / -130E programming:
#86904**89397#
HGC-600E programming:
##20022002, END and enter
SPC: "000000" or may be other
SPC typed by user.
Sony
CM-M1300/3300/Z200
programming: type "111111" and
press Jog Dial.
Choose "Programming" and
enter SPC: "000000" or may be
other SPC typed by user.
Sony CM-M1300
1. Power phone on
2. Enter six "1s" ( 111111 )
3. Press the jog dial in
4. Press the jog dial in again to
select programming
5. Enter six "0s" for the service
security code
6. Phone displays the ESN
7. Press the jog dial in for OK
8. Enter your ten digit cellular
telephone number
9. Press the jog dial in for OK
10. Enter your cellular carrier ’s
system ID (SID) without the
zeros
(Example: if your carrier ’s
system ID is 00035, enter just
35)
11. Press the jog dial in for OK
12. Enter a name for NAM 1 or
just press the jog dial in for OK
13. Phone displays Basic NAM 1
Programming is complete
14. Press the jog dial in
15. Press the jog dial in again
for EXIT
16. Phone powers itself off
17. Press the power button to
power the phone back on
18. Basic programming is
complete
Motorola
StarTAC 7760/7860
programming:
Service menu: FCN
+0+000000+000000+RCL
Test mode: FCN 00**83786633
STO
V60c programming:
Service menu: 74663 # [Menu]
[Menu] (programming code)
Test mode: [Menu] 073887 *
(security code = 000000)
Motorola Tarpon (120x)
1. Press 74663 (spells PHONE)
1. Press # MENU MENU quickly
2. Enter OTKSL
3. The work MIN will be
highlighted
4. Select the word CHANGE by
selecting the top right button
5. Select DELETE. Press and hold
the button until clear
6. Have the customer enter the
10 digit MIN number
7. Select OK with the top right
button. The “User Activation”
screen will appear
8. Scroll to highlight the CDMA
Sys ID
9. Select CHANGE by selecting
the top right button
10. Enter SID
11. Select OK by selecting the
top right button
12. Select DONE with the top
left button
13. Press the END key
14. Press # MENU MENU quickly
15. Enter OTKSL
16. The work MIN will be
highlighted
17. Select the word CHANGE by
selecting the top right button
18. Select DELETE. Press and
hold the button until clear
19. Have the customer enter
the 10 digit MIN number
20. Select OK with the top right
button. The “User Activation”
screen will appear
21. Scroll to highlight the CDMA
Sys ID
22. Select CHANGE by selecting
the top right button
23. Enter SID
24. Select OK by selecting the
top right button
25. Select DONE with the top
left button
Press the END key
Motorola Phones (ALL)
1. Enter 74663 # FCN FCN
2. Enter OTKSL
3. Enter MIN and press STO
4. Enter SID (4654) and press
STO
5. Press STO again –
programming is complete
Note: on the Tarpon (120C) you
will need to press the MENU
key instead of FCN.
Nokia
5185/6185 programming:
*3001#12345#
Software version: *#837# or
*#VER# or *#9999#
Serial / ESN: *#92772689# or
*#WARRANTY#
Phone reset: *#75681# or
*#75682#
Nokia 6185-5170
1. Press *#639#
2. Enter OTKSL and press OK
3. Enter the MIN and select OK
4. Enter the SID and select OK
5. Programming is complete
Nokia 3585
1. Enter ## followed by the
OTKSL
2. Number (MDN) is highlighted.
Press the upper left-hand soft
key to select
3. Mobile Number will display.
Enter the 10 digit MIN
4. Press OK
5. IMSI will appear. Press and
hold the Clear key until the
display is empty.
6. Enter 31000 plus the MSID (15
digits total)
7. Press the upper left hand soft
key and select OK
8. It will take you back to the
SVC Programming. Press the
upper right hand soft key to
select EXIT
9. Press END.
10. Phone will power cycle and
programming is complete.
SK Teletech
SK-IM
1000/1400/2000/2200/2400
programming:
#7583538324#626#
Getrun 2000
System NAM programming
mode: 0 + 1 + # + 7 + 3 + 7 +
SECURITY CODE (000000)
Debug menu: 0 + 1 + # + 3 + 2 +
4 + SECURITY CODE (000000)
Debug screen of field test
mode: 0 + 1 + # + 7 + 2 + 7
Test mode: 0 + 1 + # + 7 + 6 + 4
+ SECURITY CODE (000000)
System test mode: 0 + 1 + # + 7
+ 6 + 8 + SECURITY CODE
(000000)
NEOPOINT
Neopoint 1000
1. Press M to display Main Menu
2. Scroll to PREFERENCES
3. Press softkey under SELECT
4. Enter 040793
5. Scroll to PROGRAMMING
6. Press softkey under SELECT
7. Enter OTKSL
8. Press softkey under DONE
9. Scroll to PHONE NUMBER
10. Enter 10 digit MIN
11. Scroll to HOME SID
12. Enter SID (4654)
13. Press softkey under SAVE to
exit
14. Programming is complete
NEOPOINT 1600
1. Power the phone on
2. Press the "Menu" key
3. Scroll to "Preferences" -
press "Select"
4. Key in the "Field Service
Code" (the phone will not
prompt you for the code)
at the "preferences" screen to
access the "Service" menu
(Default code is "000000")
5. Scroll to "Programming" -
press "Select" - the phone will
ask for the "Subsidy Lock Code"
6. Enter the "Subsidy Lock Code
(654321)" to access the "NAM"
menu
7. Select the NAM to be
programmed (NAM 1 or NAM 2)
8. Program the NAM - Phone
number and CDMA Home SID
9. After programming has been
completed press "Save" - the
phone will reset
Audiovox
Audiovox 9100
1. Press ##
2. Enter the OTKSL
3. Display will read Service/
Menu 1 Basic …press OK
4. Next screen will read
Service Mode/Home SID…press
OK
5. Next screen will read Service
Mode/Home SID …press OK
6. Device will display Service
Menu 1. Basic #
7. Press END button to
complete programming
Handspring TREO
1. Open the flip and press the
PHONEBOOK button one time to
display the dial pad
2. Enter ## and the OTKSL using
the numbers on the Dial Pad
3. Press the handset button
shown in the diagram above
4. At the Activations screen
enter the MIN in the phone
number field using the numbers
on the device keyboard
5. Put a check in the Enable
Number Portability box and type
the MSID in the MSIN field
6. Press OK
7. The device will display the
network search pop-up and
return to the Phonebook display
Hitachi P300
1. Enter ## and the 6 digit
OTKSL
2. Press the Options soft key
and then scroll to Save Phone
#. Press the OK soft key.
3. At the NAM display scroll to
EDIT and press the OK soft key
4. Display will read NAM and
MDN will be highlighted. Press
the OK soft key.
5. At the MDN display enter the
10 digit MIN and press the SAVE
soft key.
6. At the Save prompt press the
OK soft key. The next display
will show several options that
should not edited.
7. Press the EXIT soft key and
the device will power cycle.
8. Programming is complete.
Kyosera
Kyocera 2345 1135
1. Press 111111 (#1 key 6 times)
2. Option will be highlighted
3. Press OK
4. Scroll down to Programming
5. The service programming
dialog will appear Enter Security
Code.
6. Enter the 6 digit OTSKL (code
will show as asterisks on
screen)
7. Service Options will appear
8. Scroll down to the BASIC
NAM1 Info
9. Press OK
10. Select the Phone Number by
pressing the OK key
11. Using the keypad enter the
10 digit MIN
12. Press OK
13. Press END to complete the
programming
Kyocera 6035
1. Press 1 six times (111111) and
select OPTIONS
2. Select PROGRAMMING
3. Open flip
4. Tap the OTKSL on keypad on
the screen. Tap OK
5. Tap on the PHONE NUMBER
field. Enter MIN.
6. Leave A-KEY blank
7. Enter HOME SID (4654)
8. Tap SAVE & EXIT
9. Tap YES
10. Phone will be in OFF MODE
Close flip.
Kyocera 3035
1. Press 111111 (the #1 key six
times)
2. Options will be highlighted
3. Press in the navigation key
(Navigation key is the button
located between the TALK &
END key)
4. Scroll to PROGRAMMING
using the Navigation key
5. Select PROGRAMMING by
pressing in the Navigation key
6. Enter the six digit OTKSL and
press in the navigation key
7. SERVICE OPTIONS will appear
8. Scroll down to the Basic
NAM1 info
9. Press in the navigation key
10. Clear any numbers that may
appear using the “clear” key
(arrow key located directly
below the navigation key)
11. Select the PHONE NUMBER by
pressing in the navigation key
12. Enter the 10 digit MIN select
OK by pressing in the
navigation key
13. Press END. Programming is
complete.
Kyocera 2255
1. Press the 1 key six times
(111111) “Option will be
highlighted
2. Press OK
3. Scroll down to
“ Programming” and press “OK”
4. Enter OTKSL and press the
navigation key
5. “Service Options” will appear
scroll down to the “Basic NAM1
Info”
6. Press OK
7. Select Phone Number by
pressing OK
8. Enter MIN and press OK again
9. Scroll to Home SID and press
OK
10. Enter SID (4654) and press
OK
11. Press END. Programming is
complete.
QCP 2035
1. Press 1 six times (111111)
2. Press u key to select
OPTIONS
3. Highlight PROGRAMMING and
press u key
4. Enter OTKSL
5. ESN will appear press left
arrow key to select OK
6. Enter MIN and press з key
7. Press з key again to exit -
Programming is complete
Sanyo
Sanyo 4000 4500 4700 5000
6000
1. Press ##
2. Enter the OTKSL
3. Scroll to SAVE and press OK
4. ESN will be displayed – press
OK
5. Enter 10 digit MIN and press
OK
6. Enter SID (4654) and press
OK
7. Press OK twice
8. Programming is complete
Sanyo 5150 5300 and 6400
1. Enter ## followed by the
OTKSL
2. Press MENU SAVE PHONE #
3. Press Ok
4. SVC Programming will be
displayed. Scroll and highlight
Mobile Number. Press OK
5. Press OK again
6. ESN will be displayed. Press
OK
7. Mobile Number will be
displayed enter the 10 digit MIN
press OK
8. Press OK 4 times
9. Phone will power cycle
10. Programming is complete
Sanyo 6000
1. Press ##
2. Enter OTKSL
3. Press MENU Key and scroll to
SAVE PHONE # and press OK
4. ESN will be displayed press
OK
5. Enter MIN and press OK
6. Enter SID and press OK
7. Press OK twice more
8. Programming is complete
Sanyo 4900
1. Enter ## followed by the 6
digit OTKSL
2. Press the MENU/OK key and
scroll and highlight SAVE PHONE
#
3. Press MENU/OK
4. Scroll and highlight MOBILE
NUMBER press OK
5. At the ESN display press OK
6. In the MOBILE NUMBER
screen enter your MIN and
press OK 4 times
7. At the service program menu
scroll to exit and press the
MENU/OK key.
8. Programming is complete
Sanyo 6200
1. Enter ##
2. Enter OTKSL
3. Press the MENU key and
scroll to highlight SAVE PHONE
#
4. Press OK
5. Scroll and highlight MOBILE
NUMBER
6. Press OK twice
7. Scroll and highlight EXIT
8. Press OK
9. Phone will power cycle
10. Programming is complete
Toshiba
Toshiba 2032P
1. Slide the Radio Standby
Switch on the left side of the
device to the upper side (ON)
to activate the phone function.
This is the switch with the
phone icon over it
2. After power up is completed
use the stylus to tap on the
ADMIN pull up menu at the
bottom of the screen and
select ACTIVATION WIZARD.
If your device has not yet been
activated the ACTIVATION
WIZARD will automatically start
when you turn on the radio in
your device.
3. Tap NEXT 3 times. If the
device has been previously
activated it will require only 2
presses.
4. On the fourth screen enter
the 6 digit OTKSL using
keyboard
5. Enter the MIN in both entery
fields then tap NEXT
6. Wait for the device to
initialize and display “ready to
connect”
7. To initiate IOTA tap the word
ADMIN at the bottom of the
display and then Data
Provisioning
8. Programming is complete
*******
Here is a list of various codes
to try out. Some may require an
MSL to be able to make full use
of the functionality.
##2769737 [##BROWSER] -
MiniBrowser Settings (2G)
##8626337 [##VOCODER] - Set
Vocoder
##3282 [##DATA] - Setup Menu
for Vision handsets
##8463 [##TIME] - Airtime
Menu
##040793 - Debug Menu
##786 [##RUN] - Technical
Information (be careful with
this one, you can reset the
handset)
##932 [##WEB] - IP Address
information (2G)
##889 [##TTY] - TTY On or
TTY Off
##4357 [##HELP] - Help

0 komentar:

Posting Komentar

 

Pesan

Terima Kasih Atas Kunjungan Anda Kunjungi Juga Blog Informasi D-Empires Untuk Mendapatkan Informasi Dari Segala Bidang

Site Info

Followers

File Saved Copyright © 2009 Community is Designed by Bie Blogger Template